亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

tilting furnace hydraulic cylinder Sold to America

Release time:2023-11-15 10:41:42 Hits: Current position: Home > News

This article mainly introduces:

America hydraulic cylinder,tilting furnace hydraulic cylinder manufacturer,tilting furnace hydraulic cylinder

America tilting furnace hydraulic cylinder

(America tilting furnace hydraulic cylinder,produced by Hengyu Hydraulic Co., Ltd)

tilting furnace hydraulic cylinder are widely used in America,because of high work efficiency,excellent fatigue and impact resistance,no need for deceleration device.So our company has designed tilting furnace hydraulic cylinder for customers from America.

Introduction to tilting furnace hydraulic cylinder:

The tilting furnace hydraulic cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure tilting furnace hydraulic cylinder can use 20 steel pipe, and the high pressure tilting furnace hydraulic cylinder can use 45 steel pipe.

The cavitation of the tilting furnace hydraulic cylinder has a great influence, and to avoid it, it is necessary to use the hydraulic oil reasonably and ensure the quality of the hydraulic oil. If the anti-foam property of the oil is poor, it is easy to produce foam, resulting in cavitation. Secondly, the change frequency of oil pressure is too fast and too high, which will also directly cause the formation of bubbles and accelerate the rupture rate of bubbles. The test shows that the speed of cavitation will be accelerated in the part with high frequency of pressure change. For example, at the inlet and outlet of the tilting furnace hydraulic cylinder, due to the relatively high frequency of pressure changes, the degree of cavitation is also relatively higher than that of other parts. In addition, overheating of the oil will also increase the probability of cavitation.

The assembly work of the tilting furnace hydraulic cylinder has a great impact on the quality of the tilting furnace hydraulic cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

When the tilting furnace hydraulic cylinder is in use, ensure that the tilting furnace hydraulic cylinder and the surrounding environment should be clean. The tank should be sealed to prevent contamination. Pipelines and fuel tanks should be cleaned to prevent falling off the oxide sheet and other debris. Clean with lint-free cloth or special paper. Twine and binder should not be used as sealing materials. Hydraulic oil according to the design requirements, pay attention to the change of oil temperature and oil pressure. When there is no load, unscrew the exhaust bolt for exhaust.

Answers to some questions about tilting furnace hydraulic cylinder:

How to calculate the tonnage of hydraulic cylinder? The tonnage of the cylinder refers to the output force of the cylinder under rated working pressure: 1, for single rod piston hydraulic cylinder, it can be calculated by the area of the circle corresponding to the inner diameter of the cylinder A (square centimeter), and the rated working pressure of the system p (mpa), the value is equal to 10pA kg force, and the ton is 0.01pA. 2, for the double rod piston hydraulic cylinder, with A(square centimeter) to indicate the cylinder cylinder diameter and piston rod outer diameter defined by the ring area, with p (mpa) to indicate the rated working pressure of the system, the output force of the cylinder is 0.01pA ton force.

What is the HS code of the hydraulic cylinder?
HS code of hydraulic cylinder; 8412210000 8412210000 Linear hydraulic power unit (hydraulic cylinder) 0.12000 0.35000 0.00000 0.17000 0.00000

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
玖玖资源站无码专区| 爆操大奶子美女视频| 天天干天天操天天插| 中日韩VA无码中文字幕| 日韩有码视频在线| 熟女大屁股亚洲一区| 日韩欧美一二三区| 大狼狗插阴道视频| 人妻夜夜添夜夜无码AV| 国产欧美日韩一区二区在线观看| 大鸡扒干美女BB直流水| 久久综合日韩亚洲精品色| 日韩久久奶茶视频| 骚逼少妇被巨根爆插| 国产色哟哟精选在线播放| 粉色av一区二区三区| 99精品一级欧美片免费| 大鸡巴抽插小骚逼视频免费| 澳门一区二区免费下线观看| 五月天国产成人av在线| 另类 专区 综合 中文| av在线国产哟哟| 91麻豆精品福利在线观看| 被春药女高潮抽搐喷水视频| 搞段B片黄色全免费看看| 亚洲综合一区国产精品| 欧美后入尻逼视频| 国产美女色诱视频又又酱| 久久无码免费视频| 亚洲综合欧美日韩| 操烂嫩逼内射视频| 啊啊好想被大鸡巴操视频| 五月天亚洲激情综合av| 欧美尤物操逼毛茸茸真爽| 久久精品男人的天堂av| 中文字幕欧美中日韩精品| 亚洲综合网伊人中文| 视频一区二区三区日韩视频| 久久高清中文字幕第一页| 日本成人精品一区二区三区| 国产熟女视频一区二区三区|