亚洲成人精品在线免费,日本一区二区不卡网站,精品69视频一区二区三区网站,性色α√人人爽人澡人人妻蜜臀

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

unidirectional cylinder Sold to Turkey

Release time:2023-12-21 12:32:47 Hits: Current position: Home > News

This article mainly introduces:

Turkey hydraulic cylinder,unidirectional cylinder manufacturer,unidirectional cylinder

Turkey unidirectional cylinder

(Turkey unidirectional cylinder,produced by Hengyu Hydraulic Cylinder Factory)

unidirectional cylinder are widely used in Turkey,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed unidirectional cylinder for customers from Turkey.

Introduction to unidirectional cylinder:

When the unidirectional cylinder needs to be disassembled for maintenance due to leakage and other faults, the piston should be moved to the bottom position of the unidirectional cylinder, and hard beating and sudden drop are strictly prohibited during disassembly.

When the unidirectional cylinder needs to be stored for a period of time, please follow the recommended methods: The unidirectional cylinder should be stored in a dry, clean, non-corrosive gas indoor environment, pay attention to protect the unidirectional cylinder from internal corrosion and external damage. If the indoor requirements cannot be met, the hardened and well-drained ground should be cushioned at least 30cm, and the upper part should be covered with waterproof storage. The oil unidirectional cylinder should not be in direct contact with water vapor for a long time. The unidirectional cylinder should be placed as vertically as possible with the piston rod facing up, which minimizes corrosion due to possible condensation in the unidirectional cylinder and permanent deformation of the seal due to the piston and rod weight. (When the shield is stored in the shield machine, the support shoe is placed upward). Keep the oil port protective cover until the pipe is connected. For long-term storage, the protection should be added on both sides of the piston of the unidirectional cylinder Before working, the unidirectional cylinder must be run repeatedly with low pressure (greater than the starting pressure) to discharge the air in the unidirectional cylinder before normal work. The oil inlet and outlet and the joint must be tightly fastened with a combination pad to prevent oil leakage.

If the seal of the unidirectional cylinder is abnormal wear, you can check whether the speed control valve is improperly adjusted, resulting in too high back pressure and improper installation of the seal or hydraulic oil contamination. The second is whether there is a foreign body entering the assembly and the quality of the sealing material is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and unidirectional cylinder, and the phenomenon of "pulling the unidirectional cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operation and improvement should be done according to the installation instructions.

If the unidirectional cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the unidirectional cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow unidirectional cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the unidirectional cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the unidirectional cylinder includes the leakage caused by excessive wear of the unidirectional cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and unidirectional cylinder, and the phenomenon of "pulling the unidirectional cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

Answers to some questions about unidirectional cylinder:

How to take out the diaphragm of hydraulic cylinder? The septum ring is also known as the septum sleeve, when the cylinder is too long, and does not need too much travel, add the septum sleeve, limit the stroke of the hydraulic cylinder, set on the piston rod, only contact with the guide sleeve and piston, do not cooperate with the cylinder, limit the stroke, take out the difficulty is different, need to have such a professional tool, before taking out to consult the manufacturer.

What parameters do I need to provide when purchasing hydraulic cylinders?
The main technical parameters of the hydraulic cylinder: 1. Cylinder diameter; Cylinder diameter, inner diameter size; 2. Piston rod diameter; 3. Cylinder stroke; 4. Cylinder pressure; The working pressure of the cylinder is often calculated using the test pressure, which is less than 16MPa multiplied by 1.5 and higher than 16 multiplied by 1.255. Import and export diameter and thread parameters; 6. Whether there is buffer; According to the working conditions, the piston rod extension contraction is generally buffered if the impact is large. 7. Installation method of oil cylinder, etc.

Back to list Recommended article

Leave a message if you have any questions.

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP
日韩美女在线视频一区不卡| 两人爽爽爽无码免费视频| 在线视频观看一区| 熟妇人妻无乱码中文字幕| 免看一级a一片成人欧美| 国精品午夜福利视频导航| 日韩av一区二区高清不卡| 中国老女人 操逼 视频| 天天天天天干夜夜夜夜夜操| 色噜噜噜噜一区二区三区| 欲色欲香天天网综合久久| 日韩一区二区三区国色天香| 久久精品欧美精品免费观看| 丁香婷婷亚洲六月综合色| 国产蜜月精品高清一区二区三区| 日逼动态视频免费看| 妓女综合网在线观看| 亚洲AV无码一区二区三区系列| 蜜臀AV无码国产精品尤物| 久久一区二区三区精华液介绍| 大屌把女生逼逼操肿国产| 二次元男生操女生屁眼爽| 小骚货舔小骚逼视频| 鸡巴插进缝里 日本| 久久综合娱乐中文网| 欧美精品国产一区二区在线观看| 亚洲一区二区女同性恋免费看| 精品无码一区二区三区无码| 麻豆视频一级片在线观看| 中文字幕在线观看第二页| 干女人逼逼的大几把| 日本精品高清在线观看| 美女人的逼免费观看| 中文字幕欧美人妻在线| 人妻熟女av一区二区三区| 日韩 中文字幕在线最新| 黑人大屌大战中国女| 影音先锋天堂网亚洲无码| 啊灬啊别停灬用力啊男男在线观看| 国产精品999午夜激情| 黑人大鸡巴双插美女|